1. Litter Robot III - Dump Position Fault - RobotShop Community
Meer resultaten van community.robotshop.com
Hi! I require your help regarding a problem I’m encountering. Description: My litter robot 3 recently started flashing the blue-yellow-green “cannot find dump position” error code and won’t cycle after the cats use it. If I press “reset” and then “cycle” it will cycle as normally (or almost as normally, see below) but when it returns to the home position the same error lights start flashing again. One thing I have noticed is that, when it is cycling and it reaches the end of its first turn, th...
2. Litter-Robot 3: All three lights flashing (Globe position fault)
Blue and yellow and red (All three lights flashing simultaneously): This means the unit cannot find the Dump or Home position. The unit will not cycle ...
Find solutions for your Litter-Robot 3's three lights flashing position sensors issue. Fix issues with your Connect Upgrade Kit today!
3. Litter-Robot 4: Red light bar with partial white flashing (Globe position)
If your unit displays a red light bar with partial white flashing, this indicates that the unit did not detect the globe position during its previous cycle.
Visit for solutions if your Litter-Robot 4 has a red light bar with a partial white flashing globe. Get instant support and fixes today.
4. Litter-Robot 3 Ultimate Troubleshooting Guide
3 dec 2021 · Symptom(s): Dump position error. Resolved by: Check / clean hall effect sensor. Thread(s):. Please help! Litter robot III - cannot find dump ...
The Litter Robot 3 is an incredibly popular automatic cat litter box which automatically detects when a cat has entered and exited, and rotates the main globe to sift and dump the used litter. It is subjected to conditions which most robots - if they had a choice, would prefer not to be subjected to. There's a lot of dust and debris which can cause issues, which leads to the robot not operating correctly. Customers often search online for a solution before contacting technical support, so this guide is intended to cover the most common situations.
5. Translation From Status Codes to Plain English for Notification
26 apr 2024 · I have the following notification to notify me when my Litter Robot reports a status change. The problem is that the notification sends me the 3 ...
I have the following notification to notify me when my Litter Robot reports a status change. The problem is that the notification sends me the 3 letter status code that triggered it, when what I want it to do is send me the status description, which I was able to find here. When writing logs to the logbook it uses the status description instead of the status code. I’m wondering what the easiest way would be for it to deliver the translated status description in the notification instead of the...
6. Troubleshooting Step-By-Step Guide - Litter-Robot 3
18 okt 2016 · The unit should perform an initial Clean cycle: the Globe will rotate counterclockwise to the Dump position, then rotate clockwise past the Home ...
See AlsoShoichi Ozawa NflOur convenient Litter-Robot 3 troubleshooting guide helps solve common and not-so-common problems with your unit. Learn how to quickly fix your Litter robot 3.
7. https://raw.githubusercontent.com/dcmeglio/hubitat...
/** * Litter-Robot * * Copyright 2020 Nathan Spencer * * Licensed under the ... 3 minuts: cleanCycleWaitTimeMinutes = 3 (hexadecimal representation of ...
/** * Litter-Robot * * Copyright 2020 Nathan Spencer * * Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except * in compliance with the License. You may obtain a copy of the License at: * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software distributed under the License is distributed * on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License * for the specific language governing permissions and limitations under the License. * * * Known commands that can be called: * C - start cleaning cycle: unitStatus changes from RDY to CCP; upon completion, cycleCount += 1 and unitStatus briefly goes to CCC and panelLockActive = 1 then typically returns to unitStatus of RDY and panelLockActive of previous state * D - reset settings to defaults: sleepModeActive = 0, panelLockActive = 0, nightLightActive = 1, cleanCycleWaitTimeMinutes = 7 * L0 - panel lock off: panelLockActive = 0 * L1 - panel lock active: panelLockActive = 1 * N0 - night light off: nightLightActive = 0 * N1 - night light on: nightLightActive = 1 * P0 - turn power off: unitStatus changes = OFF; on the next report from the unit, powerStatus changes to NC and cleanCycleWaitTimeMinutes shows as 7; device is still wifi connected, but won't respond to any commands except P1 (power on), sleepModeActive and panelLockActive reset...
8. Cat sensor fault sales litter robot
... dump position fault over torque fault Domestic sales, Constant Cat ... Sensor Fault LR4 r litterrobot sales, Getting Started with Litter Robot 3 sales.
Cat sensor fault sales litter robot
9. Litter-Robot 3: Fixing the globe magnets
Litter-Robot 3: Fixing the globe magnets · Blue → Yellow → Red Cycling: This means the unit cannot find the Dump position. · Red → Yellow → Blue Cycling: This ...
Troubleshooting your disassembled Litter-Robot 3 Globe? Our guide helps you check magnet positions and correct errors for a smoothly functioning unit.
10. Extracting status message and TTS from litter-robot - automation
9 nov 2022 · ... Dump + Home Position Fault", "dpf": "Dump Position Fault", "ec ... pedolsky (Pedolsky) November 9, 2022, 3:49pm 2. As I can understand ...
alias: Test - Litter Robot description: "" trigger: - platform: state entity_id: - sensor.litter_robot_status_code condition: [] action: - service: tts.google_translate_say data: entity_id: media_player.aaron_s_speakers message: [litterrobot__status_code message here] cache: true mode: single I wanted to create a TTS automation that would trigger every time the [sensor.litter_robot_status_code] changes. The trigger works, however, I need to figure out how...
